{"id":263,"date":"2020-11-08T19:18:41","date_gmt":"2020-11-08T17:18:41","guid":{"rendered":"https:\/\/sistemincalzirepardoseala.ro\/?page_id=263"},"modified":"2020-11-25T14:46:13","modified_gmt":"2020-11-25T12:46:13","slug":"tervezesi-segedlet","status":"publish","type":"page","link":"https:\/\/sistemincalzirepardoseala.ro\/en\/tervezesi-segedlet\/","title":{"rendered":"Design guide"},"content":{"rendered":"
\n\t\t\t\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Design aid for the assembly of underfloor heating without concreting <\/h1>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t
Always use safety equipment and gloves to prevent cuts or injuries. The aluminum cladding panel can be extremely sharp during bending!<\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

In case of laminated covering<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

  1. Edge insulation<\/p><\/li>

  2. Double-sided adhesive for panel fixing MAPECONTACT 2.67m\/m2<\/p><\/li>

  3. Comfort panel<\/p><\/li>

  4. RBM Tita Fix PE-RT tube \u00d816\u00d72 mm;<\/p><\/li>

  5. Preferably aluminum adhesive tape for fixing the pipe bend (requirement 1m\/m2);<\/p><\/li>

  6. Protective film<\/p><\/li>

  7. Woostep Isofloor thermo washer 1.6 mm<\/p><\/li>

  8. Laminate floor<\/p><\/li>

  9. Szeg\u00e9ly<\/p><\/li><\/ol>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

    \n\t\t\t
    \n\t\t\t\t\t\t
    \n\t\t\t\t
    \n\t\t\t\t\t

    In case of ceramic covering<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
    \n\t\t\t\t
    \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
    \n\t\t\t\t
    \n\t\t\t\t\t\t\t\t\t

    1. Edge insulation<\/p><\/li>

    2. K\u00e9toldalas ragaszt\u00f3 a panel r\u00f6gz\u00edt\u00e9s\u00e9hez MAPECONTACT<\/p><\/li>

    3. Comfort panel<\/p><\/li>

    4. RBM Tita Fix PE-RT cs\u0151 \u00d816×2 mm<\/p><\/li>

    5. Preferably aluminum adhesive tape for fixing the pipe bend (requirement 1m\/m2);<\/p><\/li>

    6. Primers<\/p>

      1. a\/ Alapoz\u00f3 (P\u00e9ld\u00e1ul PRIMER MF Mapei)<\/p><\/li>

      2. \u00a0b\/ Acrylic primer primer<\/p><\/li><\/ol><\/li>

      3. Tile adhesive<\/p><\/li>

      4. Floor board (min. dim. 25\u00d725 cm);<\/p><\/li>

      5. Mos\u00f3l\u00e1bazat<\/p><\/li><\/ol>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t

        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t

        What is the process of laying dry underfloor heating?\n<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        Ellen\u0151rizze, hogy a megl\u00e9v\u0151 fel\u00fclet, amelyen a rendszert felszerelik (sim\u00edtott cementhabarcs, cementcement, ker\u00e1mia vagy term\u00e9szetes k\u0151padl\u00f3k stb.) Mentes legyen a por \u00e9s a sz\u00e9tv\u00e1laszt\u00f3 anyagokt\u00f3l, stabil, lapos, sz\u00e1raz, emelked\u0151 nedvess\u00e9gt\u0151l \u00e9s mechanikusan ellen\u00e1ll\u00f3.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t

        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t

        Sz\u00fcks\u00e9ges eszk\u00f6z\u00f6k<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        Gy\u0151z\u0151dj\u00f6n meg r\u00f3la, hogy rendelkez\u00e9s\u00e9re \u00e1llnak a berendez\u00e9s felszerel\u00e9s\u00e9hez sz\u00fcks\u00e9ges eszk\u00f6z\u00f6k (mar\u00f3- \u00e9s \/ vagy v\u00e1g\u00f3szerkezetek, m\u00e9r\u0151-, jel\u00f6l\u0151-, cs\u0151v\u00e1g\u00f3-, henger-, fogazott sim\u00edt\u00f3 \u00e9s megfelel\u0151 egy\u00e9ni v\u00e9d\u0151eszk\u00f6z\u00f6k).<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t

        1. Edge insulation\n<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        Apply the adhesive edge insulation tape around the entire perimeter of the rooms where the radiant system is to be installed and around the perimeter of all building elements that come into contact with the system, as this should always be done with Radiant Floor Systems.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t

        2. Pre-installation of the system\n\n<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        We recommend laying the entire Comfort panel system on the substrate before final gluing. This makes it possible to recognize problems and check for additional preventive markings. It may be useful to number the panels to facilitate final installation.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t

        3. Placement of adhesive tape<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        „a”<\/h3>\n

        For gluing the panels to the substrate, we recommend the MAPEI\u00ae (*), MAPECONTACT tape (3a). This should be applied to the substrate on the two long sides of the panel, on two adjacent panels and in accordance with the center line of the panel (3b), along the entire length, in order to maximize the glued surface.

        In case the substrate is too porous or imperfectly flat, glue the panels with MAPEI\u00ae (*) (3c) or a similar cementitious ADESILEX P4 type adhesive (use suitable solvent-free adhesives that cannot attack the real EPS A panel).<\/p><\/p>\n

        <\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        „b”<\/h3>

        If you like (and only if allowed), then the use of water-based glue can usually be applied with a spatula (with 2 mm teeth). The temperature should be between 15-35\u00b0C. It is better to start from the farthest corner of the room so that you do not step on the glue. We apply the glue and let it dry until it is tacky so that the panels fit better for installation.
        The operation can take between 10 minutes and half an hour, depending on the surface and the ambient temperature.
        It is recommended to use a cement-based adhesive for tiles with a toothed spatula (with 3-4 mm teeth) for cement-based materials, especially for covering the ground floor or basement.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        „c”<\/h3>

        Panel gluing with cement-based adhesive<\/big><\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t

        4. Panel installation<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        „a”<\/h3>

        When using MAPECINACT MAPEI\u00ae (*) (4a): If the MAPECONTACT bi-adhesive tape is laid on the base, remove the protective film from the tape and carefully place the panels on it according to the assembly drawing. In the preliminary position, making sure that the panels are firmly fixed to the base.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        „b”<\/h3>

        If using a water-based adhesive (4b): Once the adhesive is on the floor and ready, place the panel, adjust and press into place. If the panels slide the glue up once, it means they are placed too early. If the adhesive has been left to dry for too long, it is generally recommended to apply another layer to the first to avoid improper bonding.
        If using a cementitious adhesive for tiles (4b): Lay the panels down before they dry. Be sure to assemble the panels and carefully remove any excess glue that comes out of the joints between the panels before it dries. In general, we recommend that you do not walk on the panels while the adhesive is drying.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        „c”<\/h3>

        If using a water-based adhesive (4b): Once the adhesive is on the floor and ready, place the panel, adjust and press into place. If the panels slide the glue up once, it means they are placed too early. If the adhesive has been left to dry for too long, it is generally recommended to apply another layer to the first to avoid improper bonding.
        If using a cementitious adhesive for tiles (4b): Lay the panels down before they dry. Be sure to assemble the panels and carefully remove any excess glue that comes out of the joints between the panels before it dries. In general, we recommend that you do not walk on the panels while the adhesive is drying.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t

        5. Cut a new groove \/ guide for the tube<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        „a”<\/h3>

        Sz\u00fcks\u00e9ges lehet egy \u00faj horony v\u00e1g\u00e1s\u00e1ra a a helysz\u00ednen, hogy egy teljes \u00e1ramk\u00f6rt tudjunk l\u00e9trehozni, k\u00fcl\u00f6n\u00f6sen akkor, ha a cs\u00f6vek csatlakoznak a gy\u0171jt\u0151h\u00f6z, vagy bizonyos kanyarokat vagy \u00fatvonalakat nem k\u00f6vetnek el\u0151re a panelen.
        A horony v\u00e1g\u00e1sa a panelen egy sniccerrel vagy elektromos horonyv\u00e1g\u00f3val t\u00f6rt\u00e9nhet, \u00fcgyelve arra, hogy olyan hornyot hozzon l\u00e9tre, amelyek megegyeznek a cs\u00f5 \u00e1tm\u00e9r\u00f5j\u00e9vel (nem t\u00fal szoros vagy nem laza) – aj\u00e1nlott 16 mm-es v\u00e1g\u00f3).
        El\u0151sz\u00f6r rajzolja fel a nyovonalat egy tollal vagy egy jel\u00f6l\u0151vel a panel fel\u00fclet\u00e9n. A cs\u00f6vek \u00edvei nem lehetnek t\u00fal szorosak (a legkisebb hajl\u00edt\u00e1si sug\u00e1r egy 16 mm-es cs\u0151 eset\u00e9ben 80 mm) (5a)<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        „b”<\/h3>

        Use a snicker or electric cutter to cut a 16mm wide and 17mm deep channel (5b) and completely remove all debris leaving the surface clean.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        „c”<\/h3>

        Cut the panel to size in the right place by removing the aluminum layer.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        „d”<\/h3>

        Place the aluminum tape on the cut groove to restore the aluminum layer (5d). Be sure to fit the aluminum tape properly to the bottom of the track so that it does not prevent the pipe from being inserted correctly.
        The connected pipe must not come out of the groove and must be covered under the surface of the panel.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t

        6. Pipe laying<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        „a”<\/h3>

        Pay attention to the grooves and panels, eliminate all disturbing circumstances.
        Insert the pipe (6a) using the duplex pipe laying method: connect the pipe to the distributor on the forward side, make sure the length is correct.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        „b”<\/h3>

        In order to protect the pipes, use a protective pipe for wall penetrations. The operation should be carried out by two people, one feeds the pipe and the other places it in the groove, use aluminum adhesive tape to fasten the curves and where the pipe protrudes from the panel for some reason. (just as we use it in the case of the \"cake\" system plate used in \"classic\" underfloor heating systems.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        „c”<\/h3>

        Secure the tube with tape where it comes out of place.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t

        7. Application of self-levelling material\n<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        If a large surface needs to be covered, it is advisable to use a self-leveling material.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t

        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        8. Installation for ceramic floors<\/strong><\/h3>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        After the floor heating has been installed, carry out the pressure test (see EN-1264 standard 6 bar 24 hours). changing the durability characteristics.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

        \n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t
        • Apply an epoxy primer to protect the aluminum on the entire surface of the panels. PRIMER MF with MAPEI\u00ae (or equivalent), roller or similar products (8a). Average requirement is 0.2 Kg\/m2.
          PRIMER MF does not change or damage PEX pipes.<\/li>
        • If PRIMER MF is used with MAPE\u00ae (or equivalent quality), apply an acrylic primer to the entire surface after 12 hours, but no later than 36 hours after application, which will help seal the tile bond later. ECOPRIM T- it is recommended with MAPEI\u00ae (or equivalent quality), with a roller. Average requirement 0.1 \u00f7 0.15 Kg\/m2.<\/li><\/ul>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t
          \n\t\t\t
          \n\t\t\t\t\t\t
          \n\t\t\t\t
          \n\t\t\t\t\t\t\t\t\t

          8. Telep\u00edt\u00e9s lamin\u00e1lt padl\u00f3 eset\u00e9n<\/strong><\/h3>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
          \n\t\t\t\t
          \n\t\t\t\t\t\t\t\t\t
          • Ha perkett\u00e1z\u00e1sra van ig\u00e9ny az adott helyis\u00e9gben, akkor a parkett\u00e1tWoostep Isofloor thermo al\u00e1t\u00e9tre kell fektetni (1,6 mm vastag).<\/li>
          • Nem sz\u00fcks\u00e9ges alapoz\u00f3t haszn\u00e1lni, de miel\u0151tt a parkett\u00e1t lerakja PE v\u00e9d\u0151f\u00f3li\u00e1t kell a Woostep Isofloor thermo al\u00e1t\u00e9t al\u00e1 rakni \u00fagyhogy a v\u00e9d\u0151f\u00f3lia 5-10 centim\u00e9teres \u00e1tfed\u00e9sben legyen egym\u00e1shozk\u00e9pest.<\/li><\/ul>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
            \n\t\t\t\t
            \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
            \n\t\t\t\t\t\t
            \n\t\t\t\t\t
            \n\t\t\t
            \n\t\t\t\t\t\t
            \n\t\t\t\t
            \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t
            \n\t\t\t
            \n\t\t\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
            \n\t\t\t\t\t\t
            \n\t\t\t\t\t
            \n\t\t\t
            \n\t\t\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t
            \n\t\t\t
            \n\t\t\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
            \n\t\t\t\t\t\t
            \n\t\t\t\t\t
            \n\t\t\t
            \n\t\t\t\t\t\t
            \n\t\t\t\t
            \n\t\t\t\t\t

            Watch our video, which shows step-by-step how you can install your own underfloor heating system!<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
            \n\t\t\t\t\t\t
            \n\t\t\t\t\t
            \n\t\t\t
            \n\t\t\t\t\t\t
            \n\t\t\t\t
            \n\t\t\t\t\t\t\t
            \n\t\t\t
            <\/div>\t\t<\/div>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t<\/div>","protected":false},"excerpt":{"rendered":"

            Tervez\u00e9si seg\u00e9dlet a betonoz\u00e1s n\u00e9lk\u00fcli padl\u00f3f\u0171t\u00e9s \u00f6ssze\u00e1ll\u00edt\u00e1s\u00e1hoz Mindig haszn\u00e1lj biztons\u00e1gi felszerel\u00e9st \u00e9s keszty\u0171t a v\u00e1g\u00e1sok vagy s\u00e9r\u00fcl\u00e9sek megel\u0151z\u00e9s\u00e9re. Az alum\u00ednium burkolat panel rendk\u00edv\u00fcl \u00e9les lehet a hajl\u00edt\u00e1s sor\u00e1n! Lamin\u00e1lt burkolat eset\u00e9n Szeg\u00e9lyszigetel\u00e9s K\u00e9toldalas ragaszt\u00f3a panel r\u00f6gz\u00edt\u00e9s\u00e9hez MAPECONTACT 2,67m\/m2 Comfort panel RBM Tita Fix PE-RT cs\u0151 \u00d816×2 mm; Lehet\u0151leg aluiminium ragaszt\u00f3szalag a cs\u0151\u00edvr\u00f6gz\u00edt\u00e9s\u00e9hez (sz\u00fcks\u00e9glet 1m \/ […]<\/p>","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"footnotes":""},"class_list":["post-263","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/sistemincalzirepardoseala.ro\/en\/wp-json\/wp\/v2\/pages\/263","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/sistemincalzirepardoseala.ro\/en\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/sistemincalzirepardoseala.ro\/en\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/sistemincalzirepardoseala.ro\/en\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/sistemincalzirepardoseala.ro\/en\/wp-json\/wp\/v2\/comments?post=263"}],"version-history":[{"count":0,"href":"https:\/\/sistemincalzirepardoseala.ro\/en\/wp-json\/wp\/v2\/pages\/263\/revisions"}],"wp:attachment":[{"href":"https:\/\/sistemincalzirepardoseala.ro\/en\/wp-json\/wp\/v2\/media?parent=263"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}